Right rudder

I never would have considered offsetting engines and rudders but it makes perfect common sense. I honestly learn a cool new fact everyday on this site lol.
 
It's not just singles. It's most anything with props that rotate in the "correct" direction (oppose airplanes that have one engine rotating in the "inappropriate" direction so that little Timmy can get his multi rating).

The Twin Bonanza, whose engines rotate in the "correct" direction, requires some right rudder on takeoff. It's not hugely pronounced, IMO.

The Brasilia was very pronounced when a power or airspeed change was made - the rudder needed to be retrimmed right away. You would hold considerable right rudder during the takeoff roll and initial climb. Many units of trim were required once airborne to get it set straight.

On the C-46, if you bring the engines up together, you may find yourself off to the races. I've not had the pleasure, but my immediate family and friends have, and you lead with the left throttle just a smidge.

The TBM-700 has a yearning to roll and yaw when you make a power lever change, which means if you cob the power at low speed, you might have some "fun" once things start catching up.
 
It's not just singles. It's most anything with props that rotate in the "correct" direction (oppose airplanes that have one engine rotating in the "inappropriate" direction so that little Timmy can get his multi rating).

The Twin Bonanza, whose engines rotate in the "correct" direction, requires some right rudder on takeoff. It's not hugely pronounced, IMO.

The Brasilia was very pronounced when a power or airspeed change was made - the rudder needed to be retrimmed right away. You would hold considerable right rudder during the takeoff roll and initial climb. Many units of trim were required once airborne to get it set straight.

On the C-46, if you bring the engines up together, you may find yourself off to the races. I've not had the pleasure, but my immediate family and friends have, and you lead with the left throttle just a smidge.

The TBM-700 has a yearning to roll and yaw when you make a power lever change, which means if you cob the power at low speed, you might have some "fun" once things start catching up.

The Saab took 1.5 units to the right for takeoff, set at the gate prior to departure.

As far as design goes, take a look at the Aero Commander. Every odd angle about that airplane was designed that way with single engine performance in mind.
 
The Saab took 1.5 units to the right for takeoff, set at the gate prior to departure.

As far as design goes, take a look at the Aero Commander. Every odd angle about that airplane was designed that way with single engine performance in mind.
Our SOP was aileron/rudder trim zero/zero, although most of the airplanes needed a unit or so either way of aileron trim because, well, crooked and bent.
 
The Q400 requires a noticeable amount of right rudder on takeoff, and since the airplane is 107ft long but only has a two axis autopilot, it also requires a fair bit of rudder pressure or trim every time you even think about moving the power levers, so we end up using the rudder trim knob about three billion times per flight.
 
The Q400 requires a noticeable amount of right rudder on takeoff, and since the airplane is 107ft long but only has a two axis autopilot, it also requires a fair bit of rudder pressure or trim every time you even think about moving the power levers, so we end up using the rudder trim knob about three billion times per flight.

With the Yaw Damp on the Saab, we never touched the rudder trim. :)
 
The Q400 has a yaw damper, but since it has very limited authority over the rudder (IIRC, something like 3 degrees of travel), it's completely overpowered by any kind of power change.

Since DHC made a ton of compromises in keeping the common type rating for the entire Dash-8 family (and keeping the airplane cheap), I wouldn't be at all surprised if they just borrowed the yaw damper from the smaller (and less powerful)
models and slapped it into the Q400.
 
On the C-46, if you bring the engines up together, you may find yourself off to the races. I've not had the pleasure, but my immediate family and friends have, and you lead with the left throttle just a smidge.
The widgeon has this issue since it doesnt have water rudders. If you don't lead with the left, you'll not be going the direction you want.
 
I fly the small Diamond 40 which requires a good amount of right rudder at the appropriate times. I can only assume this to be true with the other small single engine trainers.

However, I started thinking about the bigger single engine airplanes that I get to see here and there.

What about the Pilatus's and the Caravan's and the TBM's. Do they also require a significant amount of the rudder on the takeoff roll and the like?

It could be a stupid question but I've yet to fly in a bigger single engine.
Here's one just a teensy bit bigger...
When you jump into one of these to launch for the first time, just trim full rudder, then push the pedal to the floor, add power and hold on...
skyraider-3.jpg

1488067.jpg
 
The Saab took 1.5 units to the right for takeoff, set at the gate prior to departure.

As far as design goes, take a look at the Aero Commander. Every odd angle about that airplane was designed that way with single engine performance in mind.
We use one unit to the right.
 
Nope. I have the tops, and the captain has the bottoms until 80. At that point it becomes PF and PM.
Is that because of something unique to the Saab? On the jet I flew, the captain would usually transfer the controls on the roll if it was a rolling takeoff or once lined up.
 
Is that because of something unique to the Saab? On the jet I flew, the captain would usually transfer the controls on the roll if it was a rolling takeoff or once lined up.
I am not sure how other companies do it, so I dont know if it is a SAAB thing or company thing. @ctab5060X @jynxyjoe

Setting the power is la three step process. The Captain sets the torque 15-20% below the desired torque setting. Once the power lever is pushed past the 64 degree switch I make sure the autocoarsen goes high. Once the torque is in the proper setting I engage the APR, making sure to announce the APR is armed. Then announce the power is at whatever setting I have dialed in the CTOT box. The power is fully set about 70-80 knots.
 
Back
Top