B99 and C402 info.

If it's a 402B with Tip Tanks, be sure to burn down to 25 gals/side indicated before you switch over to AUX tank. The 414 I've been flying had a thing about trying to blow gas out if you just went by the "200 lbs" indicated.

For starting up, if it's cold (and below 25 def F), you've got to prime the hell out of it. I prime to peak and hold it for about 2 seconds, back to idle and up 1/2 inch. For Hot Starts, I push the Throttles full open, prime for 5 seconds and as you hit the start button, slowly bring the Throttle back until it catches. Your mileage may vary.

If you have any questions I might be able to answer, shoot me a pm. I've thought about applying up there as well, just so I don't have to endure a XC commute.
 
I've got time in the 402B and C and personally preferred the B as I feel it lands better. Hot and heavy is not fun, especially if one quits. You will need to plan you descents and reduce your power no more than an inch/minute to help avoid shock cooling. Good advise for surferlucas on fuel, it will blow fuel out the vents if you switch too early. Also this is technique, don't switch to the aux tanks at the same time if. I usually switched them about 10 minutes appart. That way if you have been flying all night they both won't cough at the same time when you forget to switch them. St. Elmo's fire rocks in them.

Starting the engines can be a pain but will become much easier with experience.

The 99 will be much easier to fly and you can chop and drop without a problem.
 
I agree too about the power reductions. I try to start reduction of power about 15 mins away from downwind, or setting up for approach. I cruise at 31"MP and 2400RPM (OMGZ, OVER-SQUARED!?!?!) and I plan to be at 25"MP and 2400 RPM when I'm on downwind or joining the final approach course. With the Landing Lights Out (not retracted), you'll be well within your first 15 deg of flaps speed and can get to your Vlo before the final approach fix.

21"MP to 23"MP on final to maintain Vref and just a nice easy reduction to landing, I try not to hit full idle till after the mains are on the ground.
 
I agree too about the power reductions. I try to start reduction of power about 15 mins away from downwind, or setting up for approach. I cruise at 31"MP and 2400RPM (OMGZ, OVER-SQUARED!?!?!) and I plan to be at 25"MP and 2400 RPM when I'm on downwind or joining the final approach course. With the Landing Lights Out (not retracted), you'll be well within your first 15 deg of flaps speed and can get to your Vlo before the final approach fix.

21"MP to 23"MP on final to maintain Vref and just a nice easy reduction to landing, I try not to hit full idle till after the mains are on the ground.

We didn't baby them so much, but that's always a good idea. We were always on high-speed profiles to keep up with the jet traffic into places like BOS, so it was usually 29-30", 2500(?) RPM until GS intercept, gear down flaps 15, pull off to 26", flaps 30, then 20-21" after a couple minutes at 26". 120-130 KIAS until about 200', then final flaps and pull off power to hit Vref at 50'. Works good, lasts long time.
 
We didn't baby them so much, but that's always a good idea. We were always on high-speed profiles to keep up with the jet traffic into places like BOS, so it was usually 29-30", 2500(?) RPM until GS intercept, gear down flaps 15, pull off to 26", flaps 30, then 20-21" after a couple minutes at 26". 120-130 KIAS until about 200', then final flaps and pull off power to hit Vref at 50'. Works good, lasts long time.

Probably not, I've been babying the engines on the 414 since we got it, we had 1100hrs on them when we bought it and now at 1400hrs, I'd like to see them get to TBO, if not alittle over. Last oil change, all compressions in the high 60's/low 70's...looks good, last a long time.

Today was a good day in the 414, rolled both landings on the runway...haven't had a good "greaser" in a while
 
Probably not, I've been babying the engines on the 414 since we got it, we had 1100hrs on them when we bought it and now at 1400hrs, I'd like to see them get to TBO, if not alittle over. Last oil change, all compressions in the high 60's/low 70's...looks good, last a long time.

Today was a good day in the 414, rolled both landings on the runway...haven't had a good "greaser" in a while

Yeah, they're tough to grease on. It was always luck. :) What's TBO on one of those engines? My old company was (is, I guess) approved to 2700 hours, but I don't know how many engines actually made it that far. A buddy of mine had an uncontained engine failure in one close to TBO...yes, you heard me right. Rod literally exploded out of the cowling. Good times, that. :D
 
Yeah, they're tough to grease on. It was always luck. :) What's TBO on one of those engines? My old company was (is, I guess) approved to 2700 hours, but I don't know how many engines actually made it that far. A buddy of mine had an uncontained engine failure in one close to TBO...yes, you heard me right. Rod literally exploded out of the cowling. Good times, that. :D
1600 on the 402
 
" I recently decided to further my career in the Air Force. Consequently, i headed to **CENSORED** to begin training. I was assigned to fly the **CENSORED** with a special mission of **CENSORED**. During my training event I met with rausda27, who was in my determination one of the most sincere, professional and dedicated pilots I have ever met. His skills far surpassed my own, and i was humbled to even be in the same building as he. He took me in the **CENSORED** simulator, which was the pinnacle of my already illustrious career. Now as I sit here in **CENSORED** , flying the ** CENSORED** all over this god forsaken %*&$!!, i think back fondly of my time spent with rausda27. "

Yep, I think that'll just about cover it!
 
Yeah, they're tough to grease on. It was always luck. :) What's TBO on one of those engines? My old company was (is, I guess) approved to 2700 hours, but I don't know how many engines actually made it that far. A buddy of mine had an uncontained engine failure in one close to TBO...yes, you heard me right. Rod literally exploded out of the cowling. Good times, that. :D

Victor Bravo FTW lol
 
With the 99 be careful not to slide the wheels when you land! It happens very easy when you're light, especially if you slam the flap lever up and they don't move. I opened the cargo door and saw they were still down. Raised them up, looked out (now I could see the tires) and had a big hole in the outboard tire. Looked like someone ran it on a belt sander. Needless to say CZ was not happy. If you're going where I think you're going, that's most important. Don't piss off CZ.
 
With the 99 be careful not to slide the wheels when you land! It happens very easy when you're light, especially if you slam the flap lever up and they don't move. I opened the cargo door and saw they were still down. Raised them up, looked out (now I could see the tires) and had a big hole in the outboard tire. Looked like someone ran it on a belt sander. Needless to say CZ was not happy. If you're going where I think you're going, that's most important. Don't piss off CZ.

It's real easy to flatspot the 99 tires! One of my freight dawg battle scars came when my eyebrow caught the very sharp corner of one of the gear doors while I was atttempting jiggle flaps that were stuck in the down position.
 
Back
Top